View LX838484A84B-15_2777105.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

microsemi linfinity microelectronics division 11861 western avenue, garden grove, ca. 92841, 714-898-8121, fax: 714-893-2570 page 1 copyright ? 2000 rev. 2.1d, 2001-03-15 www. microsemi . com lx8384x-xx 5a low dropout positive regulators p r o d uc ti o n a microsemi company

the lx8384/84a/84b series ics are positive regulators designed to provide 5a output current. these regulators yield higher efficiency than currently available devices with all internal circuitry designed to operate down to a 1v input-to-output differential. in each of these pr oducts, the dropout voltage is fully specified as a function of load current. dropout is guaranteed at a maximum of 1.3v (8384a) and 1.5v (8384 ) at maximum output current, decreasing at lower load currents. in addition, on-chip trimming adjusts the reference voltage tolerance to 1% maximum at room temperature and 2% maximum over the 0 to 125c range for the lx8384a, making this ideal for the pentium p54c- vre specification. the lx8384b offers 0.8% tolerance at room temperature and 1.0% maximum over line, load and temperature. fixed versions are also available and specified in the available options table below. the lx8384/84a/84b series devices are pin-compatible with earlier 3-terminal regulators, such as the 117 series products, but they do require input and output capacitors. a minimum 10f capacitor is required on the input and a 15f or greater on the output of these new devices for stability. although, these capacitors are generally included in most regulator designs. the lx8384/84a/84b series quiescent current flows into the load, thereby increasing efficiency. this feature contrasts with pnp regulators where up to 10% of the output current is wasted as quiescent current. the lx8384-xxi is specified over the industrial temperature range of -25c to 125c, while the lx8384-xxc/84a- xxc/84b-xxc is specified over the commercial range of 0c to 125c. important: for the most current data, consult microsemi s website: http://www.microsemi.com *1500f 6mv1500gx sanyo lx8384a 121 w 0.1% 218 w 0.1% in adj out 5v 3.5v at 5a 1500f 5x 6mv1500gx sanyo + + * capacitors must have < 20m w total esr for the vre specification an application of the lx8384a for the pentium p54c processors meeting vre specification. three-terminal adjustable or fixed output guaranteed < 1.3v headroom a 5a (lx8384a) guaranteed 2.0% max. reference tolerance (lx8384a) guaranteed 1.0% max. reference tolerance (lx8384b) 0.015% line regulation 0.15% load regulation

pentium ? processor vre application high efficiency linear regulators power regulators for switching power supplies battery chargers constant current regulators cyrix ? 6x86? amd-k5? lx8384/84a/84b-00 adjustable lx8384/84a/84b-15 1.5v lx8384/84a/84b-33 3.3v table 1 - available options
t a ( c) max ref accuracy max dropout voltage dt plastic to-252 (d-pak) 3-pin p plastic to-220 3-pin dd plastic to-263 3-pin 0 to 125 2.0% 1.5v lx8384-xxcdt lx8384-xxcp lx8384-xxcdd 2.0% 1.3v lx8384a-xxcdt lx8384a-xxcp lx8384a-xxcdd 1.0% 1.3v lx8384b-xxcdt lx8384b-xxcp lx8384b-xxcdd -25 to 125 2.0% 1.5v lx8384-xxidt lx8384-xxip lx8384-xxidd note: available in tape & reel. append the letter t to the part number. (i.e. lx8384-xxcpt) l l x x 8 8 3 3 8 8 4 4 x x
microsemi linfinity microelectronics division 11861 western avenue, garden grove, ca. 92841, 714-898-8121, fax: 714-893-2570 page 2 copyright ? 2000 rev. 2.1d, 2001-03-15 www. microsemi . com lx8384x-xx 5a low dropout positive regulators p r o d uc ti o n a microsemi company

power dissipation....................................................................................internally limited input voltage .................................................................................................................1 0v input to output voltage differential..............................................................................10v operating junction temperature plastic (dt, dd, p packages)................................................................................ 150c storage temperature range .......................................................................-65c to 150 c lead temperature (soldering, 10 seconds)............................................................... 300c note 1: exceeding these ratings could cause damage to the device. all voltages are with respect to ground. currents are positive into, negative out of specified terminal. dd plastic to-263 3-pin thermal resistance - junction to a mbient , q ja 60 c/w thermal resistance - junction to t ab , q jt 2.7c/w p plastic to-220 3-pin thermal resistance - junction to a mbient , q ja 60 c/w thermal resistance - junction to t ab , q jt 2.7c/w dt plastic to-252 3-pin thermal resistance - junction to a mbient , q ja 60 c/w thermal resistance - junction to t ab , q jt 2.7c/w junction temperature calculation: t j = t a + (p d x q jt ). the q ja & q jt numbers are guidelines for the thermal performance of the device/pc-board system. all of the above assume no ambient airflow.

1 v in adj / gnd* v out 2 3 tab is v out dd p ackage (3- pin ) (top view) v in v out adj/ gnd* tab is v out 3 2 1 dt p ackage (3- pin ) (top view) tab is v out adj / gnd* v out v in 1 2 3 p p ackage (3- pin ) (top view) * pin 1 is gnd for fixed voltage versions thermal limit circuit bias circuit bandgap circuit control circuit output circuit soa protection circuit current limit circuit v in adj or gnd* v out * pin 1 is gnd for fixed voltage versions p p a a c c k k a a g g e e d d a a t t a a
microsemi linfinity microelectronics division 11861 western avenue, garden grove, ca. 92841, 714-898-8121, fax: 714-893-2570 page 3 copyright ? 2000 rev. 2.1d, 2001-03-15 www. microsemi . com lx8384x-xx 5a low dropout positive regulators p r o d uc ti o n a microsemi company unless otherwise specified, the following specifications apply over the operating ambient temperature for the lx8384x-xxc with 0 c t a 125 c and the lx8384-xxi with -25 c t a 125 c except where otherwise noted. test conditions: v in -v out = 3v; i out = 5a. low duty cycle pulse testing techniques are used which maintains junction and case temperatures equal to the ambient temperature. lx8384x-xx parameter symbol test conditions min typ max units lx8384-00 / 8384a-00 / 8384b-00 (adjustable) i out = 10ma, t a = 25c 1.238 1.250 1.262 v 10ma < i out < 5a, 1.5v < (v in -v out ), v in < 10v, p < p max 1.225 1.250 1.270 v i out = 10ma, t a = 25c 1.240 1.250 1.260 v reference voltage lx8384/84a-00 (note 4) lx8384b-00 v ref 10ma < i out < 5a, 1.5v < (v in -v out ), v in < 10v, p < p max 1.238 1.250 1.262 v 1.3v < (v in -v out ), v in < 7v, i out = 10ma 0.015 0.2 % line regulation (note 2) ref (v in ) 1.3v < (v in -v out ), v in < 10v, i out = 10ma 0.035 0.3 % load regulation (note 2) ref (i out ) v out > v ref , v in - v out = 3v, 10ma < i out < 5a 0.15 0.5 % thermal regulation out (pwr) t a = 25c, 20ms pulse 0.01 0.02 % / w ripple rejection (note 3) v out = 5v, f= 120hz, c out = 100f tantalum, v in = 6.5v, c adj = 10f, i out = 5a 65 83 db adjust pin current i adj 20 55 100 a adjust pin current change (note 4) adj 10ma < i out < i out(max) , 1.3v < (v in -v out ), v in < 10v 0.2 5 a ref = 1%, i out = 5a 1.2 1.5 v dropout voltage lx8384-00 lx8384a/84b-00 ref = 1%, i out = 5a 1.1 1.3 v minimum load current i out(min) v in < 10v 2 10 ma (v in - v out ) < 7v 5 6 a maximum output current i out(max) (v in - v out ) < 10v 3 4 a long term stability (note 3) out (t) t a = 125c, 1000 hours 0.3 1 % temperature stbility (note 3) out (t) 0.25 % rms output noise (% of v out ) (note 3) out(rms) t a = 25c, 10hz < f < 10khz 0.003 % lx8384-15 / 8384a-15 / 8384b-15 (1.5v fixed) v in = 5v, i out = 0ma, t a = 25c 1.485 1.50 1.515 v 4.75v < v in < 10v, 0ma < i out < 5a, p < p max 1.470 1.50 1.530 v v in = 5v, i out = 0ma, t a = 25c 1.488 1.50 1.512 v output voltage lx8384/84a-15 (note 4) lx8384b-15 v out 4.75v < v in < 10v, 0a < i out < 5a, p < p max 1.485 1.50 1.515 v 4.75v < v in < 7v 1 3 mv line regulation (note 2) out (v in ) 4.75v < v in < 10v 1 5 mv load regulation (note 2) out (i out ) v in = 5v, 0ma < i out < i out(max) 2.5 7 mv thermal regulation out (pwr) t a = 25c, 20ms pulse 0.01 0.02 % / w ripple rejection (note 3) c out = 100f (tantalum), i out = 5a 60 83 db quiescent current i q 0ma < i out < i out(max) , 4.75v < v < 10v 4 10 ma out = 1%, i out < i out(max) 1.2 1.5 v dropout voltage lx8384-15 lx8384a/84b-15 out = 1%, i out < i out(max) 1 1.3 v e e l l e e c c t t r r i i c c a a l l s s
microsemi linfinity microelectronics division 11861 western avenue, garden grove, ca. 92841, 714-898-8121, fax: 714-893-2570 page 4 copyright ? 2000 rev. 2.1d, 2001-03-15 www. microsemi . com lx8384x-xx 5a low dropout positive regulators p r o d uc ti o n a microsemi company

unless otherwise specified, the following specifications apply over the operating ambient temperature for the lx8384x-xxc with 0 c t a 125 c and the lx8384-xxi with -25 c t a 125 c except where otherwise noted. test conditions: v in -v out = 3v; i out = 5a. low duty cycle pulse testing techniques are used which maintains junction and case temperatures equal to the ambient temperature. lx8384x-xx parameter symbol test conditions min typ max units lx8384-15 / 8384a-15 / 8384b-15 (1.5v fixed)(continued) maximum output current i out(max) v in < 7v 5 6 a temperature stability (note 3) out (t) 0.25 % long term stability (note 3) out (t) t a =125c, 1000 hours 0.3 1 % rms output noise (% of v out ) (note 3) v out (rms) t a =25c, 10hz < f < 10khz 0.003 % lx8384-33 / 8384a-33 / 8384b-33 (3.3v fixed) v in =5v, i out =0ma, t a =25c 3.267 3.30 3.333 v 4.75v < v in < 10v, 0ma < i out < 5a, p < p max 3.235 3.30 3.365 v v in =5v, i out =0ma, t a =25c 3.274 3.30 3.326 v output voltage lx8384/84a-33 (note 4) lx8384b-33 v out 4.75v < v in < 10v, 0ma < i out < 5a, p < p max 3.267 3.30 3.333 v 4.75v < v in < 7v 1 6 mv line regulation (note 2) out (v in ) 4.75v < v in < 10v 2 10 mv load regulation (note 2) out (i out ) v in =5v, 0ma < i out < i out(max) 5 15 mv thermal regulation out (pwr) t a =25c, 20ms pulse 0.01 0.02 % / w ripple rejection (note 3) c out =100f (tantalum), i out =5a 60 83 db quiescent current i q 0ma < i out < i out(max) , 4.75v < v in < 10v 4 10 ma out =1%, i out < i out(max) 1.2 1.5 v dropout voltage lx8384-33 lx8384a/84b-33 out =1%, i out < i out(max) 1 1.3 v maximum output current i out(max) v in < 7v 5 6 a temperature stability (note 3) out (t) 0.25 % long term stability (note 3) out (t) t a =125c, 1000 hours 0.3 1 % rms output noise (% of v out ) (note 3) v out (rms) t a =25c, 10hz < f < 10khz 0.003 % note 2 regulation is measured at constant junction temperature, using pulse testing with a low duty cycle. changes in output voltage due to heating effects are covered under the specification for thermal regulation. note 3 these parameters, although guaranteed are not tested in production. note 4 see maximum output current section e e l l e e c c t t r r i i c c a a l l s s
microsemi linfinity microelectronics division 11861 western avenue, garden grove, ca. 92841, 714-898-8121, fax: 714-893-2570 page 5 copyright ? 2000 rev. 2.1d, 2001-03-15 www. microsemi . com lx8384x-xx 5a low dropout positive regulators p r o d uc ti o n a microsemi company

the lx8384/84a/84b series ics are easy to use low- dropout (ldo) voltage regulators. they have all of the standard self-protection features expected of a voltage regulator: short circuit protection, safe operating area protection and automatic thermal shutdown if the device temperature rises above approximately 165c. use of an output capacitor is required with the lx8384/84a/84b series. please see the table below for recommended minimum capacitor values. these regulators offer a more tightly controlled reference voltage tolerance and superior reference stability when measured against the older pin-compatible regulator types that they replace. stability the output capacitor is part of the regulators frequency compensation system. many types of capacitors are available, with different capacitance value tolerances, capacitance temperature coefficients, and equivalent series impedances. for all operating conditions, connection of a 220f aluminum electrolytic capacitor or a 47f (<400m w esr) solid tantalum capacitor between the output terminal and ground will guarantee stable operation. if a bypass capacitor is connected between the output voltage adjust (adj) pin and ground, ripple rejection will be improved (please see the section entitled ripple rejection). when adj pin bypassing is used, the required output capacitor value increases. output capacitor values of 220f (aluminum) or 47f (tantalum) provide for all cases of bypassing the adj pin. if an adj pin bypass capacitor is not used, smaller output capacitor values are adequate. the table below shows recommended minimum capacitance values for operation. !"#$ %&'
( 10 15f tantalum, 100f aluminum none 10 47f tantalum, 220f aluminum 15f to ensure good transient response from the power supply system under rapidly changing current load conditions, designers generally use several output capacitors connected in parallel. such an arrangement serves to minimize the effects of the parasitic resistance (esr) and inductance (esl) that are present in all capacitors. cost-effective solutions that sufficiently limit esr and esl effects generally result in total capacitance values in the range of hundreds to thousands of microfarads, which is more than adequate to meet regulator output capacitor specifications. output capacitance values may be increased without limit. the circuit shown in figure 1 can be used to observe the transient response characteristics of the regulator in a power system under changing loads. the effects of different capacitor types and values on transient response parameters, such as overshoot and under-shoot, can be compared quickly in order to develop an optimum solution. lx8384x power supply in adj out star ground minimum load (larger resistor) full load (smaller resistor) r dson << r l 10ms 1 sec figure 1 - dynamic input and output test overload recovery like almost all ic power regulators, the lx8384/84a/84b regulators are equipped with safe operating area (soa) protection. the soa circuit limits the regulator's maximum output current to progressively lower values as the input-to- output voltage difference increases. by limiting the maximum output current, the soa circuit keeps the amount of power that is dissipated in the regulator itself within safe limits for all values of input-to-output voltage within the operating range of the regulator. the lx8384/84a/84b soa protection system is designed to be able to supply some output current for all values of input-to-output voltage, up to the device breakdown voltage. under some conditions, a correctly operating soa circuit may prevent a power supply system from returning to regulated opera- tion after removal of an intermittent short circuit at the output of the regulator. this is a normal mode of operation, which can be seen, in most similar products, including older devices such as 7800 series regulators. it is most likely to occur when the power system input voltage is relatively high and the load impedance is relatively low. when the power system is started cold, both the input and output voltages are very close to zero. the output voltage closely follows the rising input voltage, and the input-to-output voltage difference is small. the soa circuit therefore permits the regulator to supply large amounts of current as needed to develop the designed voltage level at the regulator output. now consider the case where the regulator is supplying regulated voltage to a resistive load under steady state conditions. a moderate input-to-output voltage appears across the regulator but the voltage difference is small enough that the soa circuitry allows sufficient current to flow through the regulator to develop the designed output voltage across the load resistance. if the output resistor is short-circuited to ground, the input-to-output voltage difference across the regulator suddenly becomes larger by the amount of voltage that had appeared across the load resistor. the soa circuit reads the increased input-to-output voltage, and cuts back the amount of current that it will permit the regulator to supply to its output terminal. when the short circuit across the output resistor is removed, all the regulator output current will again flow through the output resistor. the maximum current that the regulator can supply to the resistor will be limited by the soa circuit, based on the large input-to-output a a p p p p l l i i c c a a t t i i o o n n s s
microsemi linfinity microelectronics division 11861 western avenue, garden grove, ca. 92841, 714-898-8121, fax: 714-893-2570 page 6 copyright ? 2000 rev. 2.1d, 2001-03-15 www. microsemi . com lx8384x-xx 5a low dropout positive regulators p r o d uc ti o n a microsemi company

overload recovery (continued) voltage across the regulator at the time the short circuit is removed from the output. if this limited current is not sufficient to develop the designed voltage across the output resistor, the voltage will stabilize at some lower value, and will never reach the designed value. under these circumstances, it may be necessary to cycle the input voltage down to zero in order to make the regulator output voltage return to regulation. ripple rejection ripple rejection can be improved by connecting a capacitor between the adj pin and ground. the value of the capacitor should be chosen so that the impedance of the capacitor is equal in magnitude to the resistance of r1 at the ripple frequency . the capacitor value can be determined by using this equation: () 1 28 . 6 1 r f c r = where: c the value of the capacitor in farads; select an equal or larger standard value. f r the ripple frequency in hz r 1 the value of resistor r1 in ohms at a ripple frequency of 120hz, with r1= 100 () hz 3 . 13 100 120 28 . 6 1 = w = c the closest equal or larger standard value should be used, in this case, 15f. when an adj pin bypass capacitor is used, output ripple amplitude will be essentially independent of the output voltage. if an adj pin bypass capacitor is not used, output ripple will be proportional to the ratio of the output voltage to the reference voltage: ref out v v = m where: m a multiplier for the ripple seen when the adj pin is optimally bypassed. v ref = 1.25v for example, if v out = 2.5v the output ripple will be: 2 25 . 1 5 . 2 = = v v m output ripple will be twice as bad as it would be if the adj pin were to be bypassed to ground with a properly selected capacitor. output voltage the lx8384/84a/84b ics develop a 1.25v reference voltage between the output and the adjust terminal (see figure 2). by placing a resistor, r1, between these two terminals, a constant current is caused to flow through r1 and down through r2 to set the overall output voltage. normally this current is the specified minimum load current of 10ma. because i adj is very small and constant when compared with the current through r1, it represents a small error and can usually be ignored. lx8384x r1 r2 in adj out figure 2 - basic adjustable regulator v in i adj 50a v ref v out 2 1 2 1 r i r r v v adj ref out + ? ? ? ? ? + = load regulation because the lx 8384/84a/84b regulators are three-terminal devices, it is not possible to provide true remote load sensing. load regulation will be limited by the resistance of the wire connecting the regulator to the load. the data sheet specification for load regulation is measured at the bottom of the package. negative side sensing is a true kelvin connection, with the bottom of the output divider returned to the negative side of the load. although it may not be immediately obvious, best load regulation is obtained when the top of the resistor divider, ( r 1), is connected directly to the case of the regulator, not to the load . this is illustrated in figure 3. if r 1 were connected to the load, the effective resistance between the regulator and the load would be: ? ? ? ? + = 1 1 2 r r r r r p peff where: r p actual parasitic line resistance. when the circuit is connected as shown in figure 3, the parasitic resistance appears as its actual value, rather than the higher r peff . lx8384x r p parasitic line resistance r l r2 in adj out figure 3 - connections for best load regulation r1 v in connect r1 to case of regulator connect r2 to load a a p p p p l l i i c c a a t t i i o o n n s s
microsemi linfinity microelectronics division 11861 western avenue, garden grove, ca. 92841, 714-898-8121, fax: 714-893-2570 page 7 copyright ? 2000 rev. 2.1d, 2001-03-15 www. microsemi . com lx8384x-xx 5a low dropout positive regulators p r o d uc ti o n a microsemi company

load regulation (continued) even when the circuit is configured optimally, parasitic resistance can be a significant source of error. a 100 mil. wide pc trace built from 1 oz. c opper-clad circuit board material has a parasitic resistance of about 5 milliohms per inch of its length at room temperature. if a 3-terminal regulator used to supply 2.50 volts is connected by 2 inches of this trace to a load which draws 5 amps of current, a 50 millivolt drop will appear between the regulator and the load. even when the regulator output voltage is precisely 2.50 volts, the load will only see 2.45 volts, which is a 2% error. it is important to keep the connection between the regulator output pin and the load as short as possible, and to use wide traces or heavy-gauge wire. the minimum specified output capacitance for the regulator should be located near the regulator package. if several capacitors are used in parallel to construct the power system output capacitance, any capacitors beyond the minimum needed to meet the specified requirements of the regulator should be located near the sections of the load that require rapidly-changing amounts of current. placing capacitors near the sources of load transients will help ensure that power system transient response is not impaired by the effects of trace impedance. to maintain good load regulation, wide tr aces s hould be used on the input side of the regulator, especially between the input capacitors and the regulator. input capacitor esr must be small enough that the voltage at the input pin does not drop below v in(min) during transients. x) dropout(ma out v v v + = where: v in(min) the lowest allowable instantaneous voltage at the input pin. v out the designed output voltage for the power supply system. v dropout(max) the specified dropout voltage for the installed regulator. thermal considerations the lx8384/84a/84b regulators have internal power and thermal limiting circuitry designed to protect each device under overload conditions. for continuous normal load conditions, however, maximum junction temperature ratings must not be exceeded. it is important to give careful consideration to all sources of thermal resistance from junction to ambient. this includes junction to case, case to heat sink interface, and heat sink thermal resistance itself. junction-to-case thermal resistance is specified from the ic junction to the back surface of the case directly opposite the die. this is the lowest resistance path for heat flow. proper mounting is required to ensure the best possible thermal flow from this area of the package to the heat sink. thermal compound at the case to heat sink interface is strongly recommended. if the case of the device must be electrically isolated, a thermally conductive spacer can be used, as long as its added contribution to thermal resistance is considered. note that the case of all devices in this series is electrically connected to the output. example given: v in = 5v v out = 2.8v i out = 5.0a t a = 50c r = 2.7c/w for to-220 300 ft/min airflow available find: proper heat sink to keep ics junction temperature below 125c.** solution: the junction temperature is: a
j t ) r r (r t + + + = d p where: p d dissipated power. r t thermal resistance from the junction to the mounting tab of the package. r thermal resistance through the interface between the ic and the surface on which it is m ounted. (1.0c/w at 6 in-lbs mounting screw torque). r thermal resistance from the mounting surface to ambient (thermal resistance of the heat sink). t s heat sink temperature. t j t c t s t a r q jt r q cs r q sa first, find the maximum allowable thermal resistance of the heat sink: () cs
d a j sa r r p t t r + - - = 11.0w 5.0a 2.8v 5.0v = - = - = d d p p ) ( i ) v (v out out in(max) c/w c/w) 1.0 c/w (2.7 5.0a * 2.8v) (5.0v c 50 c 125 = + - - - = 1 . 3 r r next, select a suitable heat sink. the selected heat sink must have r < 3.1c/w. thermalloy heatsink 6296b has r = 3.0c/w with 300ft/min air flow. finally, verify that junction temperature remains within speci- fication using the selected heat sink: c 124 c 50 c/w) 3.0 c/w 1.0 c/w 11w(2.7 = + + + = j j t t ** although the device can operate up to 150c junction, it is recommended for long term reliability to keep the junction temperature below 125c whenever possible. a a p p p p l l i i c c a a t t i i o o n n s s
microsemi linfinity microelectronics division 11861 western avenue, garden grove, ca. 92841, 714-898-8121, fax: 714-893-2570 page 8 copyright ? 2000 rev. 2.1d, 2001-03-15 www. microsemi . com lx8384x-xx 5a low dropout positive regulators p r o d uc ti o n a microsemi company

10f lx8384x r1 121 w 1% r2 365 w 1% in adj out figure 4 - improving ripple rejection v in v out c1 10f* 150f + + * c1 improves ripple rejection. x c should be r1 at ripple frequency. (note a) ? c1* 10f lx8384x r1 121 w 1% r2 1k in adj out figure 5 - 1.2v - 8v adjustable regulator v in v out ** c2 100f + + * needed if device is far from filter capacitors. ? ? ? ? + = r1 r2 1 1.25v *v * out (note a) 10f 365 w 1% lx8384x 100 f 1k 1k 121 w 1% 2n3904 in adj out figure 6 - 5v regulator w ith shutdow n ttl output v in 5v + + (note a) lx8384x in adj out figure 7 - fixed 3.3v output regulator v in 3.3v 10f tantalum or 100f aluminum min. 15f tantalum or 100f aluminum capacitor. may be increased without lim it. esr m ust be less than <400m w . note a: x) dropout(ma out in(min) v ) v ( v intended + = a a p p p p l l i i c c a a t t i i o o n n s s
microsemi linfinity microelectronics division 11861 western avenue, garden grove, ca. 92841, 714-898-8121, fax: 714-893-2570 page 9 copyright ? 2000 rev. 2.1d, 2001-03-15 www. microsemi . com lx8384x-xx 5a low dropout positive regulators p r o d uc ti o n a microsemi company

p 3-pin plastic to-220 a g f q b d h c j r k l n s t u 123 m illimeters i nches dim min max min max a 14.22 15.88 0.560 0.625 b 9.65 10.67 0.380 0.420 c 3.56 4.83 0.140 0.190 d 0.51 1.14 0.020 0.045 f 3.53 4.09 0.139 0.161 g 2.54 bsc 0.100 bsc h 6.35 0.250 j 0.30 1.14 0.012 0.045 k 12.70 14.73 0.500 0.580 l 1.14 1.27 0.045 0.050 n 5.08 typ 0.200 typ q 2.54 3.05 0.100 0.120 r 2.03 2.92 0.080 0.115 s 1.14 1.40 0.045 0.055 t 5.84 6.86 0.230 0.270 u 0.508 1.14 0.020 0.045 dd 3-pin plastic to-263 a b k i f h c d 0 -8 m n j seating plane e g m illimeters i nches dim min max min max a 10.03 10.67 0.395 0.420 b 8.51 9.17 0.335 0.361 c 4.19 4.59 0.165 0.181 d 1.14 1.40 0.045 0.055 e 0.330 0.51 0.013 0.020 f 1.19 1.34 0.047 0.053 g 2.41 2.66 0.095 0.104 h 2.29 2.79 0.090 0.110 i C 1.65 C 0.065 j 0 0.25 0 0.010 k 14.60 15.87 0.575 0.625 m 7 7 n 3 3 note: dimensions do not include mold flash or protrusions; these shall not exceed 0.155mm(.006) on any side. lead dimension shall not include solder coverage. m m e e c c h h a a n n i i c c a a l l s s
microsemi linfinity microelectronics division 11861 western avenue, garden grove, ca. 92841, 714-898-8121, fax: 714-893-2570 page 1 0 copyright ? 2000 rev. 2.1d, 2001-03-15 www. microsemi . com lx8384x-xx 5a low dropout positive regulators p r o d uc ti o n a microsemi company

dt 3-pin plastic to-252 w k r x a l u o p n b d c e f g i j m q v h m illimeters i nches dim min max min max a 6.47 6.73 0.255 0.265 b 5.97 6.23 0.235 0.245 c 2.16 2.42 0.085 0.095 d 0.68 0.94 0.027 0.037 e 0.38 0.64 0.015 0.025 f 0.63 0.89 0.025 0.035 g 2.16 2.42 0.085 0.095 h 0.84 1.10 0.033 0.043 i 0.89 1.15 0.035 0.045 j 2.44 2.70 0.096 0.106 k 9.55 9.81 0.376 0.386 l 5.20 5.46 0.205 0.215 m 7.0 7.0 n 0.51 0.77 0.020 0.030 o 0.51 0.77 0.020 0.030 p 4.19 4.45 0.165 0.175 q 0.76 1.02 0.030 0.040 r 0.48 0.74 0.019 0.029 u 0.51 0.77 0.020 0.030 v 45 45 w 1.44 1.70 0.057 0.067 x 0 0.10 0 0.004 m m e e c c h h a a n n i i c c a a l l s s
microsemi linfinity microelectronics division 11861 western avenue, garden grove, ca. 92841, 714-898-8121, fax: 714-893-2570 page 11 copyright ? 2000 rev. 2.1d, 2001-03-15 www. microsemi . com lx8384x-xx 5a low dropout positive regulators p r o d uc ti o n a microsemi company

pentium is a registered trademark of intel corporation. cyrix is a registered trademark and 6x86 is a trademark of the cyrix corporation. k5 is a registered trademark of amd. production data C information contained in this document is proprietary to linfinity and is current as of publication date. this document may not be modified in any way without the express written consent of linfinity. product processing does not necessarily include testing of all parameters. linfinity reserves the right to change the configuration and performance of the product and to discontinue product at any time. n n o o t t e e s s

▲Up To Search▲

Price & Availability of LX838484A84B-15

	To Download LX838484A84B-15 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .